Pixel Buds Pro Case Issues
I've been having a hard time with my Pixel Buds Pro for a week or so. It is hard to explain but I think the case and the right earbud don't get along anymore. I'm not sure which one is at fault though.
When I have a charge on the case, and both buds in the case, the devices connect and disconnect really quickly to Bluetooth. Sometimes it charges the right one while it is doing this, sometimes it doesn't. It will actually pull down the charge on my phone while it is going on.
Any ideas? I'm 99% sure I need to replace them, but hoping there is something simple and cheap that could fix it.
Cannot reset DNS Settings
I want to undo some of my setup on my network so I can redo it in a different configuration on the same machine. The first thing I wanted to do was disable my Adguard server, making sure I could still use the internet after.
I thought I had cleared out all of the settings in my router that made it use Adguard for DNS, but when I shut down Adguard afterward, all outside connectivity fell apart. I could still get to websites if I knew their specific IP address, but nothing that needed DNS worked. When I booted Adguard back up, everything started working again.
I have tried several options in the DNS server settings in my Asus router (TUF-AX5400). Is there something I need to do in Adguard first to make this work? Or is this maybe something I need to reset in my Asus router and then give it time and a few reboots to work?
Get Better Anaerobic Stats from Runs
I consistently have a lack of anaerobic load in my Garmin training load. I did a track run today trying to work on intense intervals. I was hoping to get to the end and have more anaerobic effect than aerobic. Is there something I should be doing differently in my runs? I was under the impression that the rest phase between run intervals should allow you to really catch your breath, so I often walk for a few seconds before getting back into a jog in my rest interval.
Should I be more focused on keeping my pace up during the rest interval? Should I be running fewer/more intervals? Should I ignore these stats and just enjoy the run?
I was surprised to see Alcala optioned down to make room for Theibar. I'm not sure who I would have picked over him, but I'm guessing it was more on who could be optioned, rather than who was the least important.
I get the idea of keeping some depth around. Still a bummer for someone who seemed to be putting it together.
This was my first thought. Not sure if it is a nostalgia thing or if it was actually good at this point. I did like it a lot back then though.
I'm looking forward to the R2 coming out. My wife is due for a new car in a few years and I was surprised when she sounded interested in it too. I might just put down a reservation
So this definitely seems like the guide that helped the most. I spent more hours than I would like to admit working on this over this weekend.
I am trying to figure out if I have a way to do what I want to here. When it was all said and done I could no longer log into the remote computer I was using to run my Jellyfin server. I have been messing around a little bit using a Linux PC with that, and enjoyed that aspect of things, but it seems like once you get hardware acceleration going, you cannot see the desktop anymore. There were several warnings about this so I wasn't entirely surprised when it happened.
I think I am going to end up needing to get rid of the proxmox part, and just run Linux directly on the computer if I want to do this, and remote into it. It is currently not hooked up to a monitor and is actually on top of my kitchen cabinets out of the way. It was a fun challenge and I learned a lot I think.
Hardware Acceleration in Linux in Proxmox
I have a used Lenovo Thinkcenter 910 with a i5 7500T running Proxmox with Linux Mint in one VM and Adguard running in another. I’m just getting started so I am reading/searching for tons of answers still
I was hoping to host Jellyfin within Linux Mint. It works pretty well, but I did notice while watching a movie the CPU was pretty well pegged out. I wanted to enable hardware based acceleration but when I started reading setup guides to hope to understand what I was doing, I think I may have painted myself into a corner already.
I think I need to tell Proxmox to pass the hardware acceleration on to Linux, and then get Linux to, but also some of the things I have read make it sound like I need to have set up the VM from the beginning this way.
Am I trying to do this the hard way somehow? Does anyone have any suggestions on the best guide to follow for this?
Selected with the fifth pick in the 2014 draft, Gordon's path was derailed by a series of injuries and health issues.
> Previously loaded with talented infielders and utility men, Gordon is the second such player to be traded by the Twins in two weeks. The Twins also dealt Jorge Polanco to the Seattle Mariners on Jan. 29 in a deal that netted four players and $8 million in cash to help pay down the salary of pitcher Anthony DeSclafani.>
I will be sad to see Gordon go, but it didn't look like a good fit with the others available on the roster. He was odd man out.
Compatible M.2 SSD
It has been a long time since I have parted out computer parts and I am not sure about checking on compatibility for some types of parts. I would like to get an M.2 drive to add to my Home Assistant Yellow, and I am thinking about this one. Crucial P3 500GB PCIe M.2 2280 SSD
Is there any reason this one wont work with the Yellow?
I have never used Feit lights with Home Assistant, but yes, my bedroom lights turn on when it senses motion. That automation disables when my living room lights are off (assuming we turn them off at bedtime) or when my phone plugs in to charge (which I do at bedtime). I use a motion sensor by Phillips Hue, and it integrates directly with the Home Assistant Yellow thru its Zigbee radio without an additional hub.
This is where the 120 volt power makes it a little worse for us Americans. 2200w would be 18 amps, easily taking most of the power on a breaker.
If kettles ever got more popular in the US maybe they could put 240v outlets in kitchens for kettles, but that would be a huge change.
21 miles this week. I had to cut my 10 mile run short yesterday because it was just too hot. It was 85°F when I left for my run in the early afternoon sun. Not a real smart move, but I thought it wouldn't be so bad based on the season.
Running a half in a few weeks and wishing I had run a bit more over the last month.