My ISS is crumbling, is this common?
My ISS is crumbling, is this common?
I have a problem with my International Space Station 21321 set, all the blue clips that hold the panels to the main beams are crumbling, and weakened enough that I wake up to panels on the floor. I have no idea why this is happening, but hoping someone can help? Ideas I can do different to prevent it after I replace these parts? It seems to effect all the blue clips not just the big ones, even the little pod lost one of its solar panels :(
Some details, it's probably 4 years old now. I keep it on display but not under glass, in a 72f room. I have difficulty keeping it totally dust free as it's very fragile to begin with, but it's never really been touched otherwise.
Thanks for any ideas
Edit: not the technic connectors, the blue solar panel pattern tiles are the problem
So there's lots of good advice here for actually solving the problem, but I'm going to propose the alternative:
This is unironically the current state of the ISS, and maybe it's worth it to let art imitate real life in this case, at least until it deorbits next(?) year.
The real life one still has a few years in it. I believe the deorbit is planned for 2030
And even that date is probably a TBD soon™
honestly I'd just say get replacement pieces from Lego super easy to do if you say that they broke or whatever. I got a buch (25 or so) bricks for free because all the brown bricks kept cracking when disassembling
Definitely I'll replace the parts, just sucks if I'm going to have to fix it up every couple years
There are what? About a dozen different plastic types Lego uses? There might be a batch of plastic that was used that is slowly shrinking over time from off-gassing. (Typical bricks are ABS which don't have that particular problem.)
There might be a defect that someone else is aware of, but you might need to replace the connectors or glue them. Heck, you just need to fix the friction fit so creative use of PTFE thread tape might work.
(Not a Lego expert, but I do my research into plastics and such for other reasons. I want to guess that it might be the POM (Delrin) that is causing the issue which is absolutely not approved for use in spacecraft.)
Edit: Clarification on the PTFE thread tape use. For those who are unfamiliar with it, it's not sticky and does not have any glue on it. If anything, it's going to be a bit more slippery than other plastics. If you had two bricks and put a layer of PTFE tape between them, it's would be thin enough to act as a wedge between the bricks to fix a friction fit but you should still be able to pull the bricks apart easily. You would need to experiment though.
This is an informative answer, unfortunately it's not a matter of being loose or resizing. The clips are kind of disintegrating under the weight of supporting the piece to the crossbeam.
Ok, I misinterpreted "disintegrating" in your original post. It's unusual for parts to just crumble, so I took that to mean that parts were just falling off the build. My mistake.
Yeah, it would likely be a factory defect in the plastic. (Too much plasticizer, too little or even an incompatible dye, maybe.) Lego would probably be receptive to sending you replacements in that case as they are probably fully aware of any bad batches of plastic they had by now.
Most home windows filter out a majority of UV light from sunlight but not enough to completely prevent plastics from degrading slightly faster. Even if it got just a couple of hours of direct, filtered sunlight per day, that may have caused an issue over 4 years. (I have had plastics sag and crumble because of this over a similar time span, actually.) Just something to be aware of.
(Ozone loves to munch on plastic as well. If you have an ozone generator next to your model, that would be an issue. Some home air purifiers generate ozone, btw.)
I've had mine wall mounted for years now and haven't noticed any issues with it. Maybe your pieces were from a bad batch? LEGO has had issues in the past with certain colors becoming brittle and crumbling but AFAIK this is mainly on brown pieces.
Same, mines ok too
Is it stored in direct sunlight? Blue absorbs more UV than other colors so it might be damaged more quickly by the sun than the other blocks.
Ironic that the solar panels can handle sun.
Interesting. It does get some sun in the mornings from the window across the room but I didn't think much about it. Perhaps I'll try to relocate it too.
I second this sunlight hypothesis. Plastic and sunlight rarely play well together.
I feel like you need to @ Nasa on this
Seems like the panels are getting damaged due to cosmic rays. Needs more shielding.
You could always contact Lego. That seems like a problem with the production run or color.
And while somewhat blasmephous, if it's a display piece, you could consider glueing the things.
Yeah I think I'll do that. The specific part failing is "Modified 2 x 3 with 2 Clips with Solar Panels Pattern"
Contact LEGO support and tell them of your problems. They will usually send free replacement parts.
I've heard rumours about blue pieces being brittle. Maybe you can switch to grey pieces without spoiling the look
In my experience, the pieces that use the clip connection can sometimes become weak over time. I had one particular shelf with clips of various sets and ages that for some reason was heavily affected by the clip elements weakening in grip strength or just splitting in two; there was a bathroom with a shower on the other side of the wall, so I speculate that the humidity could have been the cause but I really don’t know. This shelf also didn’t get much sunlight, especially compared to other shelves without as much of a problem. Is there any possible source of humidity by where these clips have been weakening/breaking the most?