I used to use this docker to get the full content from its rss some time ago. You have to input the link of the page instead of the rrs link, its doesn't work on every site but it can help. Still loonking for better ones.
Ive been using gluetun with qbit for 3 years no without a worry, it would be awesome if they also added socks 5 proxy
Thank you, i will try doing it on opnsense
Update: I have installed the wol plugin from opnsense into my machine, you asked if i can send a wol packet though the router and so in my thinking i was able to do it via the plugin. The problem starts on the ARP, i found what it is and what it do but i dont know how i can insert the MAC address into the firewall rule that i created above, if you dont mind could you help me on how can i do it? And if i do that will i be able to send the wol signal though the Wlan or Wireguard in the future? Thanks
Never heard of that phrase ARP thanks i will look into that
If you can share that trick it would be great!!. Preferably i would like to use the Moonlight client wol signal but if can't, i can think of doing a script in the termux android app to send the packet
Send WoL signal though Opnsense networks
So i dont know what im doing wrong. I have 3 interfaces on opnsense
1:Server=192.168.40.0 2:Wlan=192.168.20.0 3:wireguard=192.168.60.0
And lastly the Wan with its default configuration.
I want to be able to Send a WOL packet though the Wlan network to wake up my PC that is inside Server network.
In Firewall>rules>Wlan I made a new rule like this: Action=Pass Interface=Wlan Direction=in TCP/IP=ipv4 Protocol=UDP Source=any Destination=Server address Destination port range=from 7 to 7
When i try sending a wol signal when my pc went to sleep a few minutes later i think the firewall rule goes though, but when i try to send from another device after lots of time later it doesn't go though i think.
Im using Moonlight to send its signal, does anyone have been thought this problem. Thank you
Have you tried Tachidesk-server? It's a fork of the tachiyomi app but as a self hostable, you can try downloading your mangas from there
thank you for the support, i was able to make Unbound listen to 10.50.50.0 as a dns but when i tried to access me services on 192.168.1.$$ the same problem occured. i also found another simillar post that had the same problem as mine so i now know it will not work, but thanks for the help
Yes it's because I use unbound and Adguard on opnsense, Adguard uses 5353 and unbound uses 53, so in opnsense I went to Services > Unbound DNS > query forwarding and added the IP 10.50.50.0:5353 but even doing that didn't work on my wireguard config file.
Thinking more into it the reason that It didn't work was because unbound is the primary DNS and Adguard would become the secondary DNS, if there was a way to create another IP for unbound I think my problem would be solved, but Im still learning about opnsense so I don't know how would I do it.
I didn't know that, in Adguard > Setup guide > configure your devices. Since I selected to listen to All interfaces there are lots of IP addresses so I just copied the IP from my wireguard interface like this.
But the problem is the DNS, I think the phone isn't as picky as the computer when connecting to wireguard that why it works, I will try doing that but I don't think that's the problem
How to solve identic DNS address from router through wireguard vpn
So I'm currently away from home and now I'm using the internet from another router.
My problem is that I can't access my services because the default DNS from this router is 192.168.1.1 and the DNS that I use to access my services through wireguard is also 192.168.1.1
The wireguard service comes from my own router using Opnsense and I have setup unbound+Adguard DNS as 192.168.1.1 by default so I don't know how can I solve this problem
I tried setting my computer to listen to 1.1.1.1 when connected to this wifi but when I enable my wireguard it still doesn't connect to my services I also tried enabling my Adguard to listen to All interfaces so it would enable the IP 10.50.50.0 as a DNS but I don't know much about Opnsense so it also didn't work when I changed the wireguard config file to listen to 10.50.50.0
My wireguard tunnel IP is set to 10.50.50.&& when connected to my router and the default IP when connected directly at home is the 192.168.1.&&
My phone can connect to the wireguard normally even when connected to this wifi
Does anyone had also this same problem as me could help me a little? Thank you. Sorry for the bad english
[Conclusion] i went looking into the wireguard subreddit for a smillar problem as mine and found that if the outside router uses 192.168.1.1 as the default gateway & dns when trying to connect to my tunnel ip the browser will search on the main router instead of my wireguard tunnel. I'm going to need to change my ip addresses to another ip instead of the default 192.168 Post
You can make your own infinity app using your reddit API, just follow this guide: https://www.reddit.com/r/Infinity_For_Reddit/comments/14c2v5x/build_your_own_apk_with_your_personal_api_key_in/
But if I wanted to host a Lemmy instance I would need to open ports isn't this the main issue of the post?
Interesting, I never heard of that name, will look more into it
Mmm that device is a little too expensive where I live, I think I will buy an older version of that if I decide to go that route, thank you for replying!
Noob here, could this AI feature run in a raspberry pi or some not so powerful CPUs? Do I need to enable gpu
I bought the Intel Celeron n5105 from some vendor called wooyi store on AliExpress, from what a saw on yt that CPU is a little overkill for a router and it uses too much idle power, but I think it was a good purchase for me bc I don't plan to switch this router soom. Edit: I'm also thinking between using the onboard wifi card or just buying an wifi AP to use at home, do you have some recommendations?
proxmox+pfsenseVM or just plain pfsense
I finally decided to buy a mini PC to make it as a pfsense router and I was wondering witch option is more suitable for my needs
First I was thinking of doing with proxmox so I could install pi-hole and wireguard in it but looking more into pfsense I see that there is PfblockerNG and also a Wireguard package that could be installed inside.
What does everybody in here use? I'm curious to know if thinkering in proxmox to run pfsense is more efficient than just installing bare-metal.
Thank you
Conclusion: will go with sole pfsense since I never used it in the first place, once accustomed will switch to proxmox, thank you everyone I hope there will be more posts like this in this platform