I believe that's how Mastadon users show up on Lemmy
Eddache just did a fun video about the Jetsons
Oh yeah, no discredit to the services to the consumer. On the merchant side though, they don't want to pay for the higher fees to accept the cards
I noticed that as well. Makes sense since I just got the update as well.
Device information
Sync version: v24.03.26-14:56
Sync flavor: googlePlay
Ultra user: true
View type: Cards
Push enabled: false
Device: cheetah
Model: Google Pixel 7 Pro
Android: 14
I'm guessing this is why lots of merchants don't accept American Express? Probably have the highest rates hitting the merchants
I'd give Teaching Tech's calibrations a try. His website has a great guide for tuning every part of your printer. Teaching Tech 3D Printer Calibration
I think they were just adding to the conversation
Never had a problem with mine
You said you recently got a gigabit plan, but that's related to your home download speed. Check to see what your upload speed actually is. Depending on your ISP's plans, you might have a speedy download but a slow upload.
'TomSka and Friends' has good enjoyable ads. They generally only have the one sponsor (Surfshark VPN) but they've done a lot for pushing for more enjoyable ads. Their off the rails skits are ones I don't skip
Do you have another printer to test with? Maybe it's something in the SKR Mini that's not working.
Hope it goes well!
The only thing I can think of with the extruder is thermal runaway, but Klipper would tell you if that was the case. Have you tried with no camera plugged in? If new USB cables aren't working, it might be worth starting from scratch and rebuilding your Klipper instances. If a clean Klipper install (with no webcams or anything) is breaking, then it's likely going to be a hardware issue.
How old is your Pi? I had the same issues on a generic board (Le Potato) but upgrading to a Pi 4 Model B fixed it for me. I have both my Neptune 2S (modded) and Neptune 3 Pro (stock) running on the same Pi with no issues.
Definitely change your USB cable. If you've got some complex files, maybe the cable can't handle the bandwidth (experienced this back when I was first starting out)
Lots of different ways to get into it. I personally love my Elegoo printers (An older Neptune 2S and a Neptune 3 Pro)
Need to do one of those speed/acceleration calibrations myself. I've reduced my speed for better quality, but it'd be fun to know my limits
I've used Grocy before that had good functionality for that. Can create chores that are done regularly and it can be assigned to certain people, or rotates through the family. The main feature is tracking groceries, but it does so much more.
Check out the AAWireless dongle. It's mainly for Android, but its beta version seems to have CarPlay support.
From the video's description, this is the official opening title sequence!
Nah, they actually filled them with collectible cardboard bottle caps. This is POG Racing
PrusaSlicer putting overhangs in mid-air
Anyone have any solutions for this issue? You'd think it would just bridge over the entire hole, don't know why it's doing this. We're at 195mm height here and I'd rather not run a support the entire height of the model just for this little nub.
Using version 2.6.1
Edit: Model in question https://www.thingiverse.com/thing:5551428. Not my own, but getting some fun things printed for the Spooky season
Neptune 2S extruder upgrade problems
Hello fellow printers!
I've decided to be ambitious and upgrade my printer's hotend. I followed this guide to convert my printer to a direct drive. I bought this NEMA14 motor per the instructions, but the instructions didn't specify how to wire it up to the stock Neptune 2S board. I just swapped it where the old extruder was and got everything assembled.
Started trying to tune it (Using Klipper), and things just got weird. I read that the motors can heat up while active, but this motor is getting HOT! Hot enough that it can melt PLA that's pressed up to the motor's body. Only takes a few minutes to get there, definitely can't print for long with it.
What are my next troubleshooting steps? I definitely don't want to burn my house down and will go back to my original bowden setup if needed, but I'd love to be direct drive.
Edit: Of course after I post this I finally find what's wrong. Need to tune VREF as well. I've ordered some ceramic screwdrivers to prevent accidentally frying my board and will be learning something new this weekend! Leaving this question here in case someone else needs the answer. Using this guide to tune VREF
App crashes when opened with the latest update
Updated to the latest update and the app crashes immediately. Can't get to any settings, no errors are thrown. I've had to downgrade to v23.08.31.
Anyone else having problems? I can post my device info if someone could tell me how to get that.
Edit: Device info added. Also, I do have an Ultra subscription but can't restore the purchase. That's probably since I downloaded the earlier version from APKPure.
Device information
Sync version: v23.08.31-14:10 Sync flavor: googlePlay
Ultra user: false View type: Cards Push enabled: false
Device: cheetah Model: Google Pixel 7 Pro Android: 13
I suppose this is why my hotend fan stopped working...
Took a couple failed prints to figure out something was wrong. Pulled the filament and saw it was melted WAY too high! Thankfully I've got a pack of spares, so pretty simple to swap out.
Just finished my Prusacaster
Harley Benton DIY kit ordered from Thomann, body 3d printed.
Now to learn how to play it
Finished putting together the Master Sword today!
Next step is learning to use filler, sanding, and painting