Do I have to build my own touchscreen thermostat?
Do I have to build my own touchscreen thermostat?
You're viewing a single thread.
Nah, just get one that can integrate with Home Assistant.
Nah, protect your privacy and build your own. You just need an esp board, a 4x relay board, and a thermometer sensor.
I have a heat pump as well as a furnace (for auxiliary heating). The thermostat frustrates the hell out of me! For one thing it loses its date and time (yes it has a full calendar date and time as well as time zone) if there’s even a single second power outage. How hard would it have been to put a CR2032 battery and a diode in there just to run the clock when the power fails?
For another thing, the thermostat itself runs extremely hot. Just putting my hand on it, it feels super warm to the touch. The LCD touchscreen on the other hand has molasses-slow response time. It’s almost impossible to set the temperature on the first try without overshooting by 2 degrees.
Lastly, it is designed to be able to run both the heat pump and the furnace when heating load exceeds the capacity of the heat pump. The thermostat also has a sophisticated time of day temperature set point schedule system (with separate schedules for every day of the week). However, the damn thing does not correctly reconcile these two facts!
I have the system set for cooler temperatures at night and warmer temperatures in the day. When the morning arrives and the schedule hits the higher day time set point, the thermostat suddenly sees a multiple degree deficit vs the set point and then calls for emergency furnace heating because it thinks the heat pump is failing to meet heating demand!
This is so maddening and stupid! Why can’t I have the temperature set point just continuously and cyclically vary throughout the day and night like a sine wave? No, the dumb thing runs the heating and cooling schedule as a square wave and therefore runs the furnace every single morning in order to slam the temperature up by a few degrees to the day time set point instead of gradually ramping it up over several hours with the heat pump…
Program it in increments?
My house has a lot of thermal mass. In the morning when the temperature comes up, it tends to overshoot and make the air temperature too hot after working hard to heat all that thermal mass. However I found it much more comfortable to add an increment: half an hour at a degree colder than I want. Now it can heat all that thermal mass while overheating the air is just playing into my hands
I’ve got it programmed in increments of a half a degree per hour. The thing still goes into panic mode.
Wow!
I think they might be computing the derivative of the temperature at time t in real time. When the schedule shifts to a higher set point the derivative goes to positive infinity and the system panics and calls for emergency maximum heat output.
They really ought to compute the temperature set point schedule for the whole day at once and then apply a low pass filter to that.
If we're on this subject, do you happen to know any active esp Lemmy communities?
thanks and merry christmas
Noting ESP specific to my knowledge, but there is a home assistant community.
Alright I'll check it out. Tnx:)
If my choices are a z-wave/zigbee thermostat that connects to my HomeAssistant instance and a Raspberry Pi that I have to maintain, I'll pick the z-wave one (and I did, 10 years ago. It's been rock solid.)
For my smart devices I prefer devices that can't send information over the internet no matter what. I don't want to worry about my thermostat mining bitcoin for some dude in China.
A smart thermostat is the only "smart device" I have in my home (ecobee). I figure it actually is better than something I could design in a week so it seemed worth it. Do you know of an actually competitive open hardware/open source solution?
This is the way.
And deal with breaking updates happening on HA and the thermostat software itself while simultaneously maintaining api keys and policy changes every 2-6 months.
Its hard work.
You're better off making your own thermostat relay controller
From my understanding, those days are in the past. I can't speak to that from experience because I only recently got into HA.
Depends on what proprietary WiFi controller you purchased. The one I bought for my electric underfloor heating makes me manually request new api key every 6 months. So I've had to write ANOTHER script to automate requesting a new key via their website with selenium
Now theyve put a captcha in and ive since given up. I'm too old and busy for these games so I made my own janky looking ESP relay setup